После того, как я обновился с ядра 2.6.18 до 3.5.3, у меня перестал работать переключатель режимов. Хотя lsusb показывает мой USB-модем, usb_modeswitch не переключает его. Моя системная информация приведена ниже. Я запускал lsusb, dmesg, usb-devices и usb_modeswitch, их вывод такой, как показано ниже. usb_modeswitch вместо переключения моего модема говорит: «Устройства в режиме по умолчанию не найдены. Ничего не делать. Пока.». Можете предложить решение?
Kernel: Linux 3.5.3
usb_modeswitch: 1.2.3-1
usb_modeswitch-data: 20120120-1
usbutils: 006-1
libusb: 1.0.8-0.1
root@localhost$ lsusb
Bus 002 Device 029: ID 12d1:1446 Huawei Technologies Co., Ltd.
root@localhost$ dmesg
[70112.477080] usb 2-1.4: new high-speed USB device number 30 using ehci_hcd
[70112.567757] scsi49 : usb-storage 2-1.4:1.0
[70112.567842] scsi50 : usb-storage 2-1.4:1.1
[70113.571433] scsi 49:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[70113.572304] scsi 50:0:0:0: Direct-Access HUAWEI TF CARD Storage PQ: 0 ANSI: 2
[70113.574169] sr0: scsi-1 drive
[70113.574223] sr 49:0:0:0: Attached scsi CD-ROM sr0
[70113.574250] sr 49:0:0:0: Attached scsi generic sg1 type 5
[70113.574350] sd 50:0:0:0: Attached scsi generic sg2 type 0
[70113.577173] sd 50:0:0:0: [sdb] Attached SCSI removable disk
root@localhost$ usb-devices
T: Bus=02 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#= 30 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1446 Rev=00.00
S: Manufacturer=Huawei Technologies
S: Product=HUAWEI Mobile
C: #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
I: If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
root@localhost$ cat /etc/usb_modeswitch.d/12d1\:1446
# Huawei, newer modems
TargetVendor= 0x12d1
TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506"
MessageContent="55534243123456780000000000000011062000000100000000000000000000"
root@localhost$ usb_modeswitch -c /etc/usb_modeswitch.d/12d1:1446 -v 12d1 -p 1446 -W
* usb_modeswitch: handle USB devices with multiple modes
* Version 1.2.3 (C) Josua Dietze 2012
* Based on libusb0 (0.1.12 and above)
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x12d1
DefaultProduct= 0x1446
TargetVendor= 0x12d1
TargetProduct= not set
TargetClass= not set
TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506"
DetachStorageOnly=0
HuaweiMode=0
SierraMode=0
SonyMode=0
QisdaMode=0
GCTMode=0
KobilMode=0
SequansMode=0
MobileActionMode=0
CiscoMode=0
MessageEndpoint= not set
MessageContent="55534243123456780000000000000011062000000100000000000000000000"
NeedResponse=0
ResponseEndpoint= not set
InquireDevice enabled (default)
Success check disabled
System integration mode disabled
usb_set_debug: Setting debugging level to 15 (on)
usb_os_find_busses: Skipping non bus directory devices
usb_os_find_busses: Skipping non bus directory drivers
usb_os_find_busses: Skipping non bus directory uevent
usb_os_find_busses: Skipping non bus directory drivers_probe
usb_os_find_busses: Skipping non bus directory drivers_autoprobe
Looking for target devices ...
No devices in target mode or class found
Looking for default devices ...
No devices in default mode found. Nothing to do. Bye.
Заранее спасибо.