Подкоманда «route» не существует в команде «ip» на Cisco 2960-S

Я новичок в cisco. Я использую Cisco 2960-S и определил на нем несколько VLAN. Мне нравится использовать функцию SVI и устанавливать IP-адрес 192.168.1.254 для интерфейса VLAN 1, 192.168.2.254 для интерфейса VLAN 2 и так далее, но я не могу пинговать 192.168.X.254 с самого устройства, но 192.168.1.254, хотя я выдал no shut команда для каждой конфигурации интерфейса VLAN. Мне нужна маршрутизация между VLAN. Я провел поиск и нашел несколько результатов для включения маршрутизации между VLAN, например эта ссылка, но проблема в том route подкомандование ip команда не существует:

my-net-dev(config)#ip ?
Global IP configuration subcommands:
  access-list           Named access-list
  accounting-list       Select hosts for which IP accounting information is kept
  accounting-threshold  Sets the maximum number of accounting entries
  accounting-transits   Sets the maximum number of transit entries
  address-pool          Specify default IP address pooling mechanism
  admission             Network Admission Control (NAC)
  alias                 Alias an IP address to a TCP port
  arp                   IP ARP global configuration
  auth-proxy            Authentication Proxy
  default-gateway       Specify default gateway (if not routing IP)
  device                Device tracking
  dhcp                  Configure DHCP server and relay parameters
  dhcp-client           Configure parameters for DHCP client operation
  dhcp-server           Specify address of DHCP server to use
  domain                IP DNS Resolver
  domain-list           Domain name to complete unqualified host names.
  domain-lookup         Enable IP Domain Name System hostname translation
  domain-name           Define the default domain name
  finger                finger server
  flow-aggregation      Configure flow aggregation
  flow-cache            Configure netflow cache parameters
  flow-capture          Capture additional netflow information
  flow-egress           Configure netflow egress
  flow-export           Specify host/port to send flow statistics
  flow-top-talkers      Configure netflow top talkers
  ftp                   FTP configuration commands
  gdp                   Router discovery mechanism
  gratuitous-arps       Generate gratuitous ARPs for PPP/SLIP peer addresses
  host                  Add an entry to the ip hostname table
  host-routing          Enable host-based routing (proxy ARP and redirect)
  hostname              Configure hostname types
  hp-host               Enable the HP proxy probe service
  http                  HTTP server configuration
  icmp                  ICMP options
  igmp                  IGMP global configuration
  local                 Specify local options
  name-server           Specify address of name server to use
  options               IP Options treatment
  port-map              Port to application mapping (PAM) configuration commands
  radius                RADIUS configuration commands
  rcmd                  Rcmd commands
  reflexive-list        Reflexive access list
  scp                   Scp commands
  security              Specify system wide security information
  source                IP source
  source-route          Process packets with source routing header options
  ssh                   Configure ssh options
  sticky-arp            Allow the creation of sticky ARP entries
  subnet-zero           Allow 'subnet zero' subnets
  tacacs                TACACS configuration commands
  tcp                   Global TCP parameters
  telnet                Specify telnet options
  tftp                  tftp configuration commands
  verify                URPF SNMP trap and IP packet header validation commands

Также no switchport сам по себе не работает, и после него нужно поставить подкоманду:

my-net-dev(config-if)#no switchport 
% Incomplete command.

my-net-dev(config-if)#no switchport  ?
  access         Set access mode characteristics of the interface
  autostate      Include or exclude this port from vlan link up calculation
  block          Disable forwarding of unknown uni/multi cast addresses
  host           Set port host
  mode           Set trunking mode of the interface
  nonegotiate    Device will not engage in negotiation protocol on this interface
  port-security  Security related command 
  priority       Set appliance 802.1p priority
  protected      Configure an interface to be a protected port
  trunk          Set trunking characteristics of the interface
  voice          Voice appliance attributes

ПЗУ - c2960s-universalalk9-mz.150-2.SE8.bin.