Мы сняли образ диска с IBM PS-703 (P-Series, т.е. Power-PC) BladeCenter с помощью dd. в режиме спасения. Изображение RedHat 5.11. Цели заключались в том, чтобы иметь резервный образ сервера и иметь возможность разместить этот образ на двух других серверах, одном производственном, одном резервном.
Мы построили новый сервер, используя образ на сервере IBM PS-701 (P-Series). Это будет новая производственная машина. Образ был восстановлен с помощью dd в режиме восстановления.
PS-701 загружается и работает с установленным образом резервной копии. Однако, как сообщает lspci, интерфейсов Ethernet нет. lsdev недоступен, так как образ нашей компании блокирует его во время установки.
Оригинальный PS-703 сообщает о наличии двух адаптеров Broadcom NetXtreme Ethernet. Как уже отмечалось, PS-701 не видит переходников. Последние обновления в IBM Fix Central предполагают, что 701 имеет адаптеры QLogic, но запуск lspci на другом 701 показывает, что у него есть два адаптера IBM eHEA. Мы не уверены, что правильно. Новый аппарат показывает, что прошить через АММ нельзя.
Кто-нибудь может сказать нам, как определить тип (ы) адаптеров Ethernet в 701? Кроме того, не могли бы вы сказать нам, какие драйверы нужно установить? А как сделать Ethernet видимым?
вывод dmesg добавлено по запросу Майкла Хэмптона.
На аналогичной работающей машине:
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 304 bytes per conntrack
IBM eHEA ethernet device driver (Release EHEA_0092-05)
ehea: eth0: Jumbo frames are enabled
ehea: eth0 -> logical port id #1
ehea: eth1: Jumbo frames are enabled
ehea: eth1 -> logical port id #2
ehea: eth0: Physical port up
ehea: External switch port is backup port
8021q: adding VLAN 0 to HW filter on device eth0
а с нерабочей машины:
Using pSeries machine description
Page orders: linear mapping = 24, virtual = 16, io = 12
Found initrd at 0xc000000002b80000:0xc000000002f40800
Partition configured for 16 cpus.
Starting Linux PPC64 #1 SMP Fri May 1 10:40:05 EDT 2015
-----------------------------------------------------
ppc64_pft_size = 0x1d
physicalMemorySize = 0x7a0000000
ppc64_caches.dcache_line_size = 0x80
ppc64_caches.icache_line_size = 0x80
htab_address = 0x(null)
htab_hash_mask = 0x3fffff
-----------------------------------------------------
Linux version 2.6.18-406.el5 (mockbuild@ppc-032.build.eng.bos.redhat.com) (gcc v
ersion 4.1.2 20080704 (Red Hat 4.1.2-55)) #1 SMP Fri May 1 10:40:05 EDT 2015
[boot]0012 Setup Arch
Node 0 Memory: 0x0-0x7a0000000
EEH: PCI Enhanced I/O Error Handling Enabled
PPC64 nvram contains 15360 bytes
Using dedicated idle loop
On node 0 totalpages: 499712
DMA zone: 499712 pages, LIFO batch:1
[boot]0015 Setup Done
Built 1 zonelists. Total pages: 499712
Kernel command line: root=/dev/VolGroup00/LogVol00 ro console=hvc0 rhgb quiet
[boot]0020 XICS Init
xics: no ISA interrupt controller
[boot]0021 XICS Done
PID hash table entries: 4096 (order: 12, 32768 bytes)
time_init: decrementer frequency = 512.000000 MHz
time_init: processor frequency = 3000.000000 MHz
Console: colour dummy device 80x25
Dentry cache hash table entries: 4194304 (order: 9, 33554432 bytes)
Inode-cache hash table entries: 2097152 (order: 8, 16777216 bytes)
freeing bootmem node 0
Memory: 31873344k/31981568k available (5056k kernel code, 108224k reserved, 1344
k data, 1257k bss, 320k init)
Calibrating delay loop... 1021.95 BogoMIPS (lpj=510976)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 4096
Processor 1 found.
Processor 2 found.
Processor 3 found.
Processor 4 found.
Processor 5 found.
Processor 6 found.
Processor 7 found.
Processor 8 found.
Processor 9 found.
Processor 10 found.
Processor 11 found.
Processor 12 found.
Processor 13 found.
Processor 14 found.
Processor 15 found.
Brought up 16 CPUs
Node 0 CPUs: 0-15
sizeof(vma)=176 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=216 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=96 bytes
sizeof(skbuff)=248 bytes
migration_cost=0,691
checking if image is initramfs... it is
Freeing initrd memory: 3842k freed
NET: Registered protocol family 16
PCI: Probing PCI hardware
IOMMU table initialized, virtual merging enabled
mapping IO 3dffc01f0000 -> d0000800000f0000, size: 10000
mapping IO 3dffc02f0000 -> d0000800001f0000, size: 10000
PCI: Probing PCI hardware done
Registering pmac pic with sysfs...
No pciex nodes found
No pcix nodes found
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
NET: Registered protocol family 2
IP route cache hash table entries: 1048576 (order: 7, 8388608 bytes)
TCP established hash table entries: 1048576 (order: 8, 16777216 bytes)
TCP bind hash table entries: 65536 (order: 4, 1048576 bytes)
TCP: Hash tables configured (established 1048576 bind 65536)
TCP reno registered
vio_bus_init: processing c00000079fffcd98
vio_bus_init: processing c00000079fffcf50
vio_bus_init: processing c00000079fffd088
vio_bus_init: processing c00000079fffd1e0
vio_bus_init: processing c00000079fffd338
IBM eBus Device Driver
scan-log-dump not implemented on this system
RTAS daemon started
RTAS: event: 19, Type: Platform Error, Severity: 2
audit: initializing netlink socket (disabled)
type=2000 audit(1440014763.530:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 8192 (order 0, 65536 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
alg: No test for crc32c (crc32c-generic)
ksign: Installing public key data
Loading keyring
- Added public key D8CAB7B6B14A884
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
rpaphp: RPA HOT Plug PCI Controller Driver version: 0.1
vio_register_driver: driver hvc_console registering
HVSI: registered 0 devices
Generic RTC Driver v1.07
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
brd: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Initalizing network drop monitor service
Freeing unused kernel memory: 320k freed
PCI: Enabling device: (0001:00:01.2), cmd 142
ehci_hcd 0001:00:01.2: EHCI Host Controller
ehci_hcd 0001:00:01.2: new USB bus registered, assigned bus number 1
ehci_hcd 0001:00:01.2: irq 307, io mem 0x3b00ffffd000
ehci_hcd 0001:00:01.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd 0001:00:01.0: OHCI Host Controller
ohci_hcd 0001:00:01.0: new USB bus registered, assigned bus number 2
ohci_hcd 0001:00:01.0: irq 305, io mem 0x3b00ffffe000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ohci_hcd 0001:00:01.1: OHCI Host Controller
ohci_hcd 0001:00:01.1: new USB bus registered, assigned bus number 3
ohci_hcd 0001:00:01.1: irq 306, io mem 0x3b00fffff000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
SCSI subsystem initialized
libata version 3.00 loaded.
ipr: IBM Power RAID SCSI Device Driver version: 2.5.3 (March 10, 2012)
ipr 0000:00:01.0: Found IOA with IRQ: 289
ipr 0000:00:01.0: Starting IOA initialization sequence.
ipr 0000:00:01.0: Adapter firmware version: 04200015
ipr 0000:00:01.0: IOA initialized.
scsi0 : IBM 57D0 Storage Adapter
Vendor: IBM-ESXS Model: ST9600204SS Rev: B541
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 1172123568 512-byte hdwr sectors (600127 MB)
sda: Write Protect is off
sda: Mode Sense: df 00 10 08
SCSI device sda: drive cache: write through w/ FUA
SCSI device sda: 1172123568 512-byte hdwr sectors (600127 MB)
sda: Write Protect is off
sda: Mode Sense: df 00 10 08
SCSI device sda: drive cache: write through w/ FUA
sda: sda1 sda2 sda3
sd 0:2:0:0: Attached scsi disk sda
Vendor: IBM Model: VSBPD1BK SAS Rev: 01
Type: Enclosure ANSI SCSI revision: 02
scsi: unknown device type 31
Vendor: IBM Model: 57D0001SISIOA Rev: 0150
Type: Unknown ANSI SCSI revision: 00
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.11.6-ioctl (2011-02-18) initialised: dm-devel@redhat.com
device-mapper: dm-raid45: initialized v0.2594l
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
type=1404 audit(1440014784.958:2): selinux=0 auid=4294967295 ses=4294967295
sd 0:2:0:0: Attached scsi generic sg0 type 0
scsi 0:8:0:0: Attached scsi generic sg1 type 13
scsi 0:255:255:255: Attached scsi generic sg2 type 31
lp: driver loaded but no devices found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.6 loaded
loop: loaded (max 8 devices)
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 50102144k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across
:50102144k
Loading iSCSI transport class v2.0-871.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
libcxgbi:libcxgbi_init_module: tag itt 0x1fff, 13 bits, age 0xf, 4 bits.
libcxgbi:ddp_setup_host_page_size: system PAGE 65536, ddp idx 3.
Chelsio T3 iSCSI Driver cxgb3i v2.0.0 (Jun. 2010)
iscsi: registered transport (cxgb3i)
IPv6: Loaded, but administratively disabled, reboot required to enable
cnic: Broadcom NetXtreme II CNIC Driver cnic v2.5.12 (June 29, 2012)
Broadcom NetXtreme II iSCSI Driver bnx2i v2.7.2.2 (Jun 18, 2012)
iscsi: registered transport (bnx2i)
iscsi: registered transport (tcp)
iscsi: registered transport (iser)
iscsi: registered transport (be2iscsi)
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 304 bytes per conntrack
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 2 ports detected
usb 1-1.2: new high speed USB device using ehci_hcd and address 3
usb 1-1.2: configuration #1 chosen from 1 choice
hub 1-1.2:1.0: USB hub found
hub 1-1.2:1.0: 4 ports detected
usb 1-1.2.3: new high speed USB device using ehci_hcd and address 4
usb 1-1.2.3: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Vendor: MATSHITA Model: UJDA780 DVD/CDRW Rev: CA22
Type: CD-ROM ANSI SCSI revision: 00
scsi 1:0:0:0: Attached scsi generic sg3 type 5
usb-storage: device scan complete
usb 1-1.2.3: reset high speed USB device using ehci_hcd and address 4
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
usb 1-1: USB disconnect, address 2
usb 1-1.2: USB disconnect, address 3
usb 1-1.2.3: USB disconnect, address 4
usb 1-1: new high speed USB device using ehci_hcd and address 5
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 2 ports detected
usb 1-1.2: new high speed USB device using ehci_hcd and address 6
usb 1-1.2: configuration #1 chosen from 1 choice
hub 1-1.2:1.0: USB hub found
hub 1-1.2:1.0: 4 ports detected
usb 1-1.2.3: new high speed USB device using ehci_hcd and address 7
usb 1-1.2.3: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 7
usb-storage: waiting for device to settle before scanning
Vendor: MATSHITA Model: UJDA780 DVD/CDRW Rev: CA22
Type: CD-ROM ANSI SCSI revision: 00
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
sr 2:0:0:0: Attached scsi CD-ROM sr0
sr 2:0:0:0: Attached scsi generic sg3 type 5
usb-storage: device scan complete
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
Вы можете разместить вывод dmesg?
Вообще говоря, лучший способ понять это - заглянуть в модуль управления шасси. У него должна быть возможность перечислять устройства в блейд-сервере.
(Я бы прокомментировал, но низкая репутация)
РЕДАКТИРОВАТЬ: У меня больше нет действующего права на поддержку IBM, поэтому я не могу связать вас напрямую, но похоже, что у вас есть модель eHEA. На страницах поддержки PS701 должны быть драйверы. Кроме того, здесь есть драйвер с открытым исходным кодом: http://sourceforge.net/projects/ibmehcad/
Я все равно рекомендую вам проверить CMM на предмет полной инвентаризации оборудования блейд-сервера, потому что я просто предполагаю на основе других ваших выходных данных. Другой вариант - попробовать lsvpd, который вы получите, только если установите инструменты поддержки / обслуживания IBM (или запустите AIX).